|
|||||||||||||||||||||||||||||||||
|
Home | Training | Equipment | Travel | Rental | Repair | Contact Us |
|||||||||||||||||||||||||||||||||
|
Service/Repair
Manufacturer Warranty and Non-Warranty Regulator Service: $89.95
Note: If your regulator has a manufacturer's warranty that covers annual service parts and you have fulfilled all of the terms of your warranty then you are not charged for annual service kits. You may still be charged for parts that are not covered under a manufacturer's warranty. Scubapro/UWATEC Warranty | Oceanic Warranty | Atomic Warranty | Zeagle Warranty TUSA Warranty | Mares/DaCor Warranty
Scubaland Adventures Warranty Regulator Service: $59.95In addition to a Manufacturer's warranty...Scubaland Adventures offers an additional lifetime warranty on regulator life support equipment. The Scubaland warranty is valid as long as your equipment is serviced once a year. The warranty gives you the following benefits:
How do I get a Scubaland Adventures warranty?1. All regulators purchased from Scubaland after February 1, 2006 at full retail value are automatically enrolled in the Scubaland warranty program. 2. Any regulator, purchased from Scubaland or another authorized dealer, may be enrolled in the warranty program for $150. When you enroll your regulator and life support equipment in the program you will receive your first service at no charge.
Note: If your regulator has a manufacturer's warranty that covers annual service parts and you have fulfilled all of the terms of your warranty then you are not charged for annual service kits. You may still be charged for parts that are not covered under a manufacturer's warranty. Scubapro/UWATEC Warranty | Oceanic Warranty | Atomic Warranty | Zeagle Warranty TUSA Warranty | Mares/DaCor Warranty Visual Inspections: $20.00Ask about a year's worth of free air fills. Purchase a free air sticker when you get your tank visually inspected and get your inspection for free!
Oxygen Cleaning Services: $25 valve-$50 tankFirst the cylinder is visually inspected (see above) and completely disassembled and cleaned using a special O2 compatible cleaner from Global Manufacturing. All parts are cleaned in the ultrasonic cleaner, rinsed and reassembled using ONLY CHRISTOLUBE. All stickers and markings are checked to PSI, OSHA and CGA Standards. After completion the first fill is done on site. Remember to service your regulator yearly to maintain your warranty. If you have a Scubapro regulator whose warranty has lapsed, you can reinstate your warranty by purchasing parts this year. Then the following years your parts are free as long as your get your regulator serviced every year. Packing for your trip? Notice something not right? We do rush repairs. Ask for details. Attention Tech Divers! We also do O2 cleaning for tanks, valves, and regulators.
|
Important Info Ask about Factory Upgrades! To keep your gear in good condition, remember to keep your equipment out of the heat. Also, rinse your gear after diving (salt and chlorine water can degrade o-rings). We do rush repairs - ask for details |
|||||||||||||||||||||||||||||||
Scubaland services most major
brands including Apollo, Atomic, Dacor, Mares, Oceanic, Scubapro, TUSA and Zeagle.
We also service and repair most brands of spear guns. All repairs are done
on-site by a certified and licensed technician. We have a one week
turnaround for service/repair unless parts need to be ordered. 
During the initial break down of the
regulator, all parts are inspected for cracks, undue wear and fatigue. After
complete disassembly all parts are introduced to the ultrasonic cleaner for
removal of all solvents, debris and salt. Once all parts are thoroughly cleaned
and rinsed, then the reassembly begins. Using only factory authorized parts and
oxygen compatible grease (christolube) all parts are assembled to manufacturer’s
recommendations. All o-rings included with the service kit are replaced and
anything that does not meet standards will need approval from the owner before
replacement. The first stage regulator is adjusted and set within manufacturer’s
standards and the second stage and octo are adjusted to operate precisely with
the first stage.
All cylinders are inspected
by certified inspectors, properly trained in cylinder inspections to PSI, OSHA,
and CGA Standards. The cylinder is inspected for current and appropriate
markings then the tank is completely drained, all accessories, stickers and the
valve will be removed. The external inspection will identify heat damage,
re-painting, odors, bows, bulges and line corrosion forming around tank boots.
The internal inspection will identify cracks, pitting, surface rust and
oxidation. The threads of the cylinder are inspected for cracks, missing and\or
damaged threads. The valve is then inspected for the correct burst disk, the
o-ring is replaced and the dip tube is verified to be present and secure. The
threads are greased with DOW Corning 111 to prevent electrolysis. If the
cylinder has meet all standards with in the PSI, OSHA and CGA Standards, the
cylinder is reassembled and issued a current visual inspection sticker, good for
one year with in the same month. If the cylinder does not meet standards the
tank will be permanently marked and condemned for service.|
Copyright (c) 2006 Scubaland Adventures, Inc. All Rights Reserved Photos and Video Copyright (c) 2006 Scubaland Adventures, Inc., All Rights Reserved |
Serving Austin, Georgetown, Waco, Killeen, |
|||||